Drilling Speed and Feed Calculator

Calculate theoretical drill rpm, axial feed, and constant-feed travel time from cutting diameter and cutting parameters you supply.

Your inputs

Inches accept decimals and fractions. Millimeters accept decimals. Changing units reinterprets the numbers; it does not convert them.

Positive decimal from applicable tooling data, not spindle rpm.
Length per full turn in selected dimension unit; not per flute or per minute.
Nonnegative length including any travel you intend to count. Enter 0 to omit travel time.

Enter your values or load the labeled example.

Your result

Waiting for your inputs

Your results will appear here after calculation.

User-supplied cutting speed and feed per revolution for the actual tool, material, and setup. Continuous constant-speed axial feed only; no material recommendations, machine limits, pecking, approach, breakthrough allowance, or cycle-time guarantee.

Translate tooling parameters into rpm and axial feed

When preparing a permitted hole in door hardware or a mounting plate, use cutting parameters that apply to the actual drill, material, and setup. This calculator converts those supplied parameters into theoretical spindle speed and axial feed. It does not select a cutting speed for steel, aluminum, wood, or another material.

Rocky Mountain Twist’s drilling speeds and feeds calculator describes the relationship between drill diameter, surface feet per minute, rpm, and inches per revolution. Its relationship uses a rounded coefficient; this calculator uses 12/π before rounding the final output. Material recommendations from a chart should not be transferred to a different tool or application without checking their conditions.

Diameter and surface speed determine rpm

At the cutting diameter, one revolution travels a circumference of πD. To maintain cutting surface speed V, revolutions per minute must be V divided by that circumference. For diameter in inches and surface speed in feet per minute:

rpm = 12 × SFM ÷ (π × diameter in inches)

The factor 12 converts feet to inches. For a millimeter diameter and speed in meters per minute, the corresponding factor is 1,000. The two input-unit controls are independent: selecting millimeters for dimensions does not change a speed entered as SFM. Exact length conversion follows NIST’s inch definition.

At a fixed surface speed, doubling drill diameter halves rpm. This relationship does not account for a machine’s available speed settings, power, rigidity, runout, coolant, or tool wear. Compare the theoretical result with the applicable tool instructions and machine limits before choosing an actual setting.

Feed per revolution is not feed per minute

Enter the total axial feed per revolution, in the selected length unit. Do not enter feed per flute, feed per tooth, or an already calculated feed per minute. Multiplying the per-revolution feed by rpm gives linear axial feed:

Axial feed per minute = feed per revolution × rpm

The optional time question uses a supplied total feed travel: seconds = travel ÷ axial feed per minute × 60. Enter zero travel to get zero time while still calculating rpm and feed. A drill’s full-diameter depth may not equal its total axial travel because the point extends farther. Include only travel that you intend to count and can define from the actual operation.

Work through a hypothetical half-inch drill

Use 0.5 in diameter, 100 SFM, 0.005 in/rev, and 1 in total axial feed travel. These are demonstration inputs, not recommended settings for a door or material.

Quantity Independent relationship Displayed result
Spindle speed 1,200 ÷ (0.5π) 763.944 rpm
Axial feed 763.943726… × 0.005 3.820 in/min
Metric axial feed 3.819718… × 25.4 97.021 mm/min
Ideal feed time 1 ÷ 3.819718… × 60 15.708 s

The equivalent metric inputs are 12.7 mm diameter, 30.48 m/min surface speed, 0.127 mm/rev, and 25.4 mm travel. They produce the same physical result. Intermediate calculations do not use the rounded rpm or feed shown in the result panel.

Keep a travel estimate separate from a drilling cycle

The time result assumes constant speed and continuous feed over exactly the entered travel. It excludes setup, approach, dwell, pecking, retraction, tool changes, acceleration, and interruptions. It is not a production cycle-time promise, and a hand-fed operation may not maintain the calculated feed.

A positive diameter, surface speed, and feed per revolution are required. Zero is valid only for travel. The tool reports three-decimal approximations; display precision does not establish achievable machine accuracy or permission to modify a rated door assembly.

Review machining geometry inputs before working from a door-hardware drawing. Countersink depth answers a separate cone-geometry question; router template offset answers a guide-to-cutter offset question. Neither provides drilling parameters for this calculator.