Countersink depth calculator

Calculate ideal countersink depth or conical drill-point height and tip depth from diameters, included angle, and your stated full-diameter depth.

Your inputs

Inches accept decimals and fractions. Millimeters accept decimals. Changing units reinterprets the numbers; it does not convert them.

Countersink: diameter at the entry surface. Drill point: full cutting diameter.
Drill-point mode only. Nonnegative; 0 gives the ideal point height alone.
Full included angle, greater than 0 and less than 180. Use your drawing or tool data.

Enter your values or load the labeled example.

Your result

Waiting for your inputs

Your results will appear here after calculation.

Ideal coaxial cone: countersink to a through-hole intersection, or pointed cone from its full-diameter plane to its tip. Drill mode adds your full-diameter depth from the entry surface. Actual point/web geometry, setup travel, screw seating, tolerances, strength, and allowed modification are not checked.

Depth of an ideal conical countersink

A countersink widens the mouth of a through-hole with a cone. This tool finds the axial distance from the major-diameter surface to the circle where the cone meets the through-hole. That distance is different from a drill’s total travel or a countersink tool’s overall length.

Enter the major diameter at the surface, the through-hole diameter, and the full included cone angle shown on your drawing or cutter data. The angle is not the half-angle between one cone wall and the axis. The tool supplies no default screw-head angle.

Derive the depth from a section

In an axial section, one half of the cone forms a right triangle. Its radial width is half the diameter difference. The angle at the cone axis is half the included angle θ, so:

Radial difference = (D − d) ÷ 2
Axial depth = (D − d) ÷ [2 tan(θ ÷ 2)]

Here D is the surface diameter and d is the through-hole diameter. A larger diameter difference increases the depth. For the same diameters, a wider included angle makes the cone shallower. These are geometric effects; they do not specify the correct countersink for a screw or the amount of material an installation may remove.

Check a 90-degree example

With D = 1/2 in, d = 1/4 in, and θ = 90°, the radial difference is 1/8 in. Since tan 45° = 1, the depth is exactly 0.125 in = 3.175 mm in the ideal model.

Using 12.7 mm and 6.35 mm for the diameters gives the same depth. If both diameters are doubled with the angle unchanged, the depth doubles to 0.250 in. If the two diameters are equal, there is no conical widening; countersink mode rejects that case because it requires D > d > 0.

Relate an ideal drill point to full-diameter depth

The ideal drill-point mode uses the same axial cone section with a pointed tip instead of an inner through-hole intersection. Enter the full drill diameter, full included point angle, and required full-diameter depth from the entry surface. It ignores the through-hole field used by countersink mode.

Ideal point height h = D ÷ [2 tan(θ ÷ 2)]
Ideal tip depth from entry surface = required full-diameter depth + h

For a hypothetical 1/2 in diameter, 90° included point angle, and 1 in full-diameter depth, the point height is 0.250 in and the tip reaches 1.250 in below the entry surface. With 12.7 mm diameter and 25.4 mm full-diameter depth, those results are 6.350 mm and 31.750 mm. A zero full-diameter depth is valid and returns the point height alone. The 90° example is a convenient triangle, not a recommended drill angle.

This assumes an exact straight-sided pointed cone, with the tip depth measured from the work surface. Real drill points may have a web, chisel edge, split point, or another profile; use the actual tool geometry when that difference matters. The result excludes approach distance, machine zero offsets, breakthrough allowance, pecking, retraction, and permission to drill a door or hardware component. It is not automatically the machine’s commanded travel.

For a constant-feed time estimate, the drilling speed and feed calculator accepts a separately defined total axial feed travel. Decide which travel the operation actually includes before transferring a value; do not add the point height again if it is already included.

Angle and display limits

The included angle must be greater than 0° and less than 180°. Near 0°, a small angle produces a very deep cone; near 180°, depth approaches zero. Neither endpoint describes a finite, ordinary countersink under this formula.

Numerical trigonometry makes the displayed depth approximate. Results use three decimal places without rounding intermediate values. A very small positive depth can display as 0.000; the display is not a machining tolerance. Inputs accept up to 12 decimal places, with fractional inches also supported for the diameters.

Compare against the actual assembly

The calculation assumes a coaxial, straight-sided cone and a circular cylindrical through-hole. It does not include screw-head fillets, head recesses, a cutter’s tip geometry, material deformation, fastener seating, remaining wall strength, or restrictions on modifying listed hardware or a door assembly.

Use the relevant screw, hardware, and tool drawings to decide what geometry is permitted. If you already have a measured depth and an explicit acceptable interval, dimensional comparison checks that interval separately. The unit conversion uses the exact inch–millimeter relationship; the depth formula above is derived directly from the right-triangle tangent definition.