Door swing geometry calculator

Find a point’s position, straight-line displacement, and arc travel around a fixed pivot.

Your inputs

Measure from the fixed rotation axis to the point you want to track, not automatically the door width.
0 to 180. Top view: start along +x; positive rotation is counterclockwise toward +y. This is not a handing convention.

Ideal planar rotation of one point. Radius must be positive and no more than 1 billion inches (25.4 billion mm), a software limit.

Enter your values or load the labeled example.

Your result

Waiting for your inputs

Coordinates, straight-line displacement, and arc travel for one point around a fixed pivot.

One point in an ideal plane. Door thickness, pivot offsets, obstacles, clear opening width, and handing are not assessed.

Track one point around a pivot

Use this calculator to describe the ideal top-view movement of a point on a rotating door. Measure the distance from the actual fixed pivot axis to that point. The point could be on the latch edge, but its radius is not automatically the nominal door width.

The outputs describe one point. They do not describe the whole door’s occupied area or the available clear opening.

Coordinate reference

Place the pivot at (0, 0). At 0°, the tracked point is at (r, 0) on the positive x axis. Viewed from above, positive rotation is counterclockwise toward the positive y axis. At 90° the point is at (0, r); at 180° it is at (−r, 0).

Use this mathematical reference consistently when relating results to a drawing. It is not a left-hand or right-hand door designation. The calculator supports one rotation from 0° through 180°, including both endpoints.

Coordinates, displacement, and travel

For radius r and angle θ in radians:

x = r cos θ
y = r sin θ
Straight-line displacement = 2r sin(θ ÷ 2)
Arc travel = rθ
θ in radians = degrees × π ÷ 180

Coordinates locate the final point relative to the pivot. Straight-line displacement is the chord from the starting point to the final point. Arc travel is the distance the point follows around the circle. These are different quantities even though they all use length units.

Input and display rules

Enter a positive radius in inches or millimeters. Inches accept decimals and fractions such as 36 1/2; millimeters and degrees accept decimals. The radius limit is 1 billion inches, equivalent to 25.4 billion mm, solely to bound numerical calculations. It is not a door-size recommendation.

Results use numerical trigonometry and are approximate. Displays round to three decimal places without rounding intermediate values; small nonzero values may display as zero. Display precision is not a clearance allowance or a measurement accuracy claim.

Worked examples

A 36-inch radius through 90°

With r = 36 in and θ = 90° = π/2 radians:

  • Final coordinates: x = 0.000 in, y = 36.000 in, or (0.000, 914.400) mm.
  • Straight-line displacement: 36√2, approximately 50.912 in or 1,293.157 mm.
  • Arc travel: 18π, approximately 56.549 in or 1,436.336 mm.

Entering 914.4 mm as the radius produces the same physical result. These values illustrate the point model; they do not establish a clear opening width.

Closed and half-turn positions

At 0°, the same point is at (36, 0) in with zero displacement and arc travel. At 180°, it is at (−36, 0) in, with a 72 in chord and arc travel 36π, approximately 113.097 in. The negative x coordinate means the point has passed the y axis; it is not a negative radius.

Apply the result to a drawing

Locate the true pivot and tracked point before entering the radius. Door thickness, offset pivots, hardware projections, the frame, stops, walls, and other obstacles require their own geometry. The tool does not check collisions, a swept area, net opening width, accessibility, egress, or manufacturer clearance requirements.

For physical installation, use the actual door and hardware drawings. A mathematically valid point location does not prove the complete assembly can move through that angle.

FAQs

Is arc travel the same as displacement?

No. Arc travel follows the circular path. Displacement here is the straight chord between the starting and final point positions. Except at zero rotation, the arc is longer.

Does 90° mean my door is fully open?

It means a quarter-turn from the defined starting radius. The model does not determine the door’s physical stop, available angle, or clear opening.

Sources

OpenStax, University Physics Volume 1, §10.1, Rotational variables defines positive counterclockwise rotation and the relationship between angle, radius, and arc length. The coordinates follow the sine and cosine definitions; the chord follows from bisecting the isosceles triangle between the two radii. These are geometric relationships, not product installation instructions. See References for length units.