Calculate the moment of one force
Find the magnitude of the torque produced by one force about a pivot, or solve for the force that produces a stated torque at that geometry. Both modes use the pivot-to-application-point distance and the angle between the outward radius and the force vector. The inverse mode answers a one-force load case; it does not determine an actual door’s opening resistance or select a closer.
Measure the radius and angle
The radius r runs from the pivot axis to the point where the force is applied. The included angle φ is between that outward radius and the force vector. A perpendicular force has φ = 90°. A force along the radius has φ = 0° or 180° and produces zero torque about that pivot.
The force-to-radius angle is not automatically the door opening angle. If a force stays perpendicular to the door as it moves, the included angle remains 90° even while the door’s opening angle changes.
Formula and units
Torque magnitude τ = rF sin φ
Perpendicular moment arm = r sin φ
Use the full pivot-to-force distance as r. If you already have a perpendicular moment arm, enter it as the distance with 90°; do not apply the angle correction twice.
Force is entered in pound-force (lbf) or newtons (N). Length uses inches or millimeters. The outputs are lbf·in, lbf·ft, and N·m. Pounds of mass and kilograms are not force inputs. Do not substitute a door’s weight estimate for the applied opening force.
The conversion uses 1 lbf = 4.4482216152605 N, from the exact pound mass relationship and standard gravity of 9.80665 m/s². This is the definition of the unit, not a local-gravity estimate. One foot is exactly 12 inches.
Input and display rules
Force may be zero; the radius must be positive. Enter an included angle from 0° through 180°. Inch distances accept fractions; force, millimeters, and degrees accept decimals. Numerical software limits are 1 billion inches for radius and 1 billion newtons for force, with the equivalent force bound applied to lbf inputs. These limits are not hardware ratings.
In force mode, enter torque in lbf·in, lbf·ft, or N·m. Its value must be nonnegative, and the calculated force must remain within the same software limit. Torque and distance units have separate selectors: 25 lbf·ft and a 30 in radius must be converted to a consistent length basis before division.
Results are numerical approximations displayed to three decimal places, without intermediate display rounding. Small nonzero torques can round to zero. The result is a magnitude: it does not specify clockwise or counterclockwise direction or sum other torques.
Worked examples
Perpendicular force
For F = 10 lbf, r = 30 in, and φ = 90°, sine is 1:
τ = 30 × 10 = 300 lbf·in = 25 lbf·ft.
In SI units, 300 × 0.0254 × 4.4482216152605 = 33.8954487083… N·m. Displays are 300.000 lbf·in, 25.000 lbf·ft, and 33.895 N·m.
Force at 30° to the radius
For the same force and distance with φ = 30°, sine is 1/2. Torque is 150.000 lbf·in, 12.500 lbf·ft, or 16.948 N·m after three-decimal rounding. At 0° or 180°, torque is zero because the force’s line of action passes through the pivot.
Metric inputs
For 10 N applied perpendicular to a 1,000 mm radius, torque is 10 × 1 = 10 N·m, displayed as 10.000 N·m, 88.507 lbf·in, and 7.376 lbf·ft.
Solve for force without confusing the angles
For a positive moment arm, rearranging the same relationship gives F = τ / (r sin φ). This is the magnitude of the single force at the stated application point and direction. With a hypothetical 300 lbf·in moment and 30 in radius, the force is 10.000 lbf at 90°, or 20.000 lbf at 30°. The shorter perpendicular arm at 30° requires twice the force for the same moment.
| Radius | Force-to-radius angle | Force for 300 lbf·in |
|---|---|---|
| 30 in | 90° | 10.000 lbf |
| 15 in | 90° | 20.000 lbf |
| 30 in | 30° | 20.000 lbf |
The inverse is undefined at 0° and 180°. At those angles, every force along the radius produces zero torque: a positive target cannot be produced, and a zero target does not identify one particular force. Force mode therefore rejects both endpoints, even for zero torque. At any supported angle strictly between them, a zero target gives zero force. Near an endpoint, a small moment arm can require a very large force; a rounded zero torque display is not a sound starting value for the inverse.
Use the original stated torque rather than a three-decimal result copied from another calculation. Reversing a rounded display can change the implied force. If the stated torque represents one opposing moment, the result is the force contribution needed to balance that moment under the chosen geometry; other moments and actual motion still need their own model.
Interpret the load case
This is the torque contribution of the one force entered. It is not the net torque of a door assembly. Closer torque curves, hinge friction, seals, pressure differences, multiple forces, inertia, and changing force directions need additional information.
An opening-force or accessibility assessment requires the applicable procedure, measurement location, door condition, and jurisdiction. The calculator does not compare the result with a legal limit, infer closer size, or approve hardware capacity.
FAQs
Why is 90° the largest torque for the same force and radius?
The entire force acts perpendicular to the radius at 90°. At another included angle, only the perpendicular component contributes to this torque magnitude.
Can I enter a tightening-torque specification?
Force mode can translate a stated moment into a one-force magnitude at your stated radius and angle. It does not establish the correct tightening torque, tool accuracy, or installation procedure for a fastener.
Sources
OpenStax, University Physics Volume 1, §10.6, Torque explains the cross product, torque magnitude rF sin φ, and the perpendicular lever arm. NIST SP 811 conversion factors lists force and torque units; its displayed lbf factor is rounded. NIST footnote 23 gives the exact standard-gravity basis. These sources support mechanics and units, not a specific door product or compliance decision.