Door and Frame Thermal Expansion Calculator

Compare unconstrained door and frame dimensional changes from separate lengths, supplied expansion coefficients, and temperature differences.

Your inputs

Inches accept decimals and fractions. Millimeters accept decimals. Changing units reinterprets the numbers; it does not convert them.

Positive dimension along the comparison axis at its reference temperature.
Nonnegative decimal from applicable material or assembly data; e.g. 0.000012, not 12.
Signed decimal difference in the selected temperature unit; zero is valid.
Positive dimension along the same axis; define its endpoints independently.
Nonnegative decimal valid for this dimension and temperature range.
Signed decimal difference; the door and frame may have different changes.

Enter your values or load the labeled example.

Your result

Waiting for your inputs

Your results will appear here after calculation.

Two independent, uniformly heated or cooled, unconstrained linear dimensions with coefficients you supply. Coefficients are always per °C; temperature differences may use °C or °F. The difference is not an actual installed gap, a clearance requirement, or a fire-door modification assessment. No moisture swelling, bowing, gradients, constraints, or composite response.

Compare dimensional response to temperature

A door dimension and a frame dimension can change by different amounts when their materials or temperatures differ. This calculator compares two independently defined free linear dimensional changes. It helps check the arithmetic behind a thermal movement assumption before comparing it with an actual door assembly drawing.

It does not predict an installed door gap. Hinges, anchors, constraints, coatings, composite construction, nonuniform sunlight, and moisture can change the physical response. A door that binds cannot be diagnosed from two expansion coefficients alone.

Define the dimension and its reference temperature

For each object, identify both endpoints of a dimension along the same comparison axis. A door width and an inside frame span are possible records, but the material data must support applying the model to those particular dimensions. An inside frame opening does not necessarily expand like an unconstrained bar of the same nominal span.

Enter each dimension at its own stated reference temperature, its applicable nonnegative linear expansion coefficient, and its final-minus-reference temperature difference. Use the survey sheet to retain endpoints, material or assembly identification, source revision, reference temperature, and constraints. Do not assume the door and frame undergo the same temperature change.

Calculate free linear change

OpenStax, University Physics Volume 2, §1.3 describes the linear approximation:

ΔL = α × L(reference) × ΔT

The coefficient α is always entered per °C, as an ordinary decimal. For example, 12 × 10⁻⁶ per °C is entered as 0.000012, not 12. Values here are examples, not assigned properties of a particular door. Obtain the coefficient and its valid range from material or assembly data. The supported input model accepts zero or positive coefficients; materials requiring a negative coefficient are outside this version.

For Fahrenheit temperature differences, the tool converts Δ°C = Δ°F × 5/9. There is no subtraction of 32 because this is a difference, not an absolute temperature. The coefficient field stays per °C even when the temperature difference uses °F.

Heating gives positive change for a positive coefficient; cooling gives negative change. Zero temperature change or a zero coefficient gives zero dimensional change. Dimensions must remain positive under the stated linear model. This numerical check does not establish that the linear approximation is physically valid for a large temperature excursion.

Interpret frame change minus door change

Relative dimensional change = ΔL(frame) − ΔL(door)

A positive result means the entered frame dimension increases more, or decreases less, than the door dimension. A negative result means the door dimension increases more, or decreases less. It does not specify which edge moves or how that change distributes between two sides.

Only if the frame dimension really represents an independently expanding opening span, and both dimensions follow the assumed free behavior, could their difference describe the change in total span surplus. This tool does not add an initial gap or decide whether an assembly meets clearance, fire-door, or installation requirements. Use door leaf dimensions for a separate stated opening-and-gap dimension chain.

Work through a hypothetical width comparison

Assume two 36 in reference dimensions. Give the door a coefficient of 0.000012 per °C, the frame 0.000024 per °C, and each a 50°C increase. No particular material or product is assigned these example properties.

Quantity Independent calculation Exact result
Door free change 36 × 0.000012 × 50 0.0216 in = 0.54864 mm
Frame free change 36 × 0.000024 × 50 0.0432 in = 1.09728 mm
Frame minus door change 0.0432 − 0.0216 0.0216 in = 0.54864 mm

The relative change displays as 0.022 in and 0.549 mm. These rounded numbers represent the same underlying result; they are not installation tolerances. Equivalent inputs are 914.4 mm reference dimensions or 90°F temperature increases. The same positive coefficients with −50°C changes produce a relative change of −0.0216 in.

Recognize conditions that need a different assessment

The linear model assumes each dimension responds uniformly and freely with an applicable approximately constant coefficient. It excludes moisture swelling in wood, layered construction, thermal gradients, bowing, differential movement along a member, mechanical restraint, and thermal stress. An exterior surface temperature alone may not describe the full door section.

Do not turn this arithmetic result into a universal trimming allowance or an explanation for every seasonal sticking problem. Record actual measurements and environmental conditions, then obtain the relevant assembly guidance. Frame geometry can analyze measured planar corners; dimensional chain bounds can propagate bounds you explicitly supply. Neither substitutes for a verified thermal or moisture model of the installed assembly.