Thread Lead and Travel Calculator

Calculate ideal thread lead and axial travel from threads per inch or axial pitch, start count, and revolutions.

Your inputs

Inches accept decimals and fractions. Millimeters accept decimals. Changing units reinterprets the numbers; it does not convert them.

Positive decimal; always per inch, regardless of dimension unit.
Positive length, not lead for a multiple-start thread.
Whole number, 1–100 (software limit). Verify from the drawing.
Nonnegative decimal; 0.25 means a quarter-turn. No fractions.

Enter your values or load the labeled example.

Your result

Waiting for your inputs

Your results will appear here after calculation.

Ideal mating threads with no backlash, deformation, or slip. Start count is the number of independent helices, not turns. Travel is a magnitude, not tightening direction, engagement, screw length, clamping force, or a hardware adjustment recommendation.

Relate a turn to axial movement

A known thread pitch can turn a measured rotation into an ideal axial movement. This is useful when interpreting an adjustable threaded hardware component’s drawing. The result describes motion along the thread axis; it does not establish how far a latch, hinge, or other connected mechanism moves.

For a single-start thread, one full turn advances by one pitch. Atlantic Fasteners’ explanation of nut and bolt travel gives the inch relationship 1/TPI and the corresponding metric pitch relationship. Its single-start examples do not establish the thread form, start count, or allowable adjustment of a particular lock component.

Pitch and lead describe different distances

Pitch is the axial distance between adjacent thread forms. Lead is the axial advance in one complete revolution. A multiple-start thread has several independent helices, so lead is the pitch multiplied by the number of starts. Count starts from the drawing or actual thread ends; the number of turns you make is a different input.

Pitch (in) = 1 ÷ TPI
Lead = pitch × starts
Ideal axial travel = lead × revolutions

These relationships define the ideal helix geometry. For a two-start thread, two neighboring pitches are traversed during a revolution along one helix. This doubles the lead without changing the distance between adjacent thread forms.

Input Meaning Example
TPI Threads per axial inch, always per inch 20 TPI means 0.05 in pitch
Axial pitch Distance between neighboring forms, in the selected unit 1.27 mm equals 0.05 in
Starts Independent thread helices 1 for a verified single-start thread
Revolutions Full turns, entered as a decimal 0.25 for a quarter-turn

Selecting millimeters does not turn TPI into threads per millimeter. In TPI mode, the pitch is still 1/TPI inches; both output units describe the same movement. In pitch mode, the selected unit applies to the entered pitch. Switching modes clears the result and ignores the inactive pitch field.

A 20 TPI quarter-turn example

Suppose a hypothetical component has 20 TPI, one start, and is rotated 0.25 revolution. Its pitch and lead are both 1/20 = 0.05 in. Travel is:

0.05 × 0.25 = 0.0125 in = 0.3175 mm

The three-decimal display is 0.013 in / 0.318 mm. The unrounded travel is shown separately so the display does not imply the movement was 0.013 in exactly. The NIST inch definition supplies the exact 25.4 mm conversion.

Entering 1.27 mm pitch in pitch mode gives the same result. Changing to two starts gives lead 0.1 in / 2.54 mm per revolution and quarter-turn travel 0.025 in / 0.635 mm. The two-start example explains the model; it is not a statement about ordinary lock-hardware threads.

Interpret ideal travel before adjusting hardware

The output is a nonnegative movement magnitude. Left-hand versus right-hand thread, viewing side, which member rotates, and which member is restrained determine the actual movement direction. Do not infer tightening direction from a positive result.

Backlash can consume part of a rotation before axial movement occurs. Elastic deformation, damaged threads, stops, linkage ratios, and clearances can also make the component’s actual response differ. Thread pitch alone does not prove thread compatibility: diameter, form, class, handedness, and the applicable product requirements remain separate checks.

Use the manufacturer’s permitted adjustment procedure and range. The calculator does not determine tightening torque, clamping force, remaining engagement, safe screw length, or whether a door assembly may be modified. A zero revolution input returns zero ideal movement; a zero pitch or TPI cannot define this calculation. Start count is limited to whole numbers from 1–100 as a software boundary.

If the question is a stack of physical layers, use stacked thickness. If a bolt moves inside an elongated opening, use slot travel. Those dimensions should not be inferred from thread travel.