Define a circular segment, not an arbitrary arch
The chord-and-rise method uses the inner chord span c, rise h above its chord, and a nonnegative outward radial depth d. It supports minor circular arcs up to a semicircle, 0 < h ≤ c/2. The three-point method instead defines the circle and selected arc from three ordered coordinates. Both methods make the outer arc concentric, using the same endpoint rays and outer radius R + d.
Radius and lengths
Chord-and-rise mode: R = c²/(8h) + h/2; α = 2 atan(2h/c)
Inner arc = 2Rα; outer arc = 2(R+d)α
Outer chord = 2(R+d)sinα; outer rise = (R+d)(1−cosα)
Three-point mode: u = P2−P1; v = P3−P1
Solve 2u · C = |u|² and 2v · C = |v|²; center = P1+C; R = |C|
θ = 2 atan2(|ux·vy−uy·vx|, u · v−|u|²)
Inner arc = Rθ; outer arc = (R+d)θ; θ is in radians
The chord-and-rise equations follow the right triangle between circle center, chord midpoint, and endpoint. Angles are in radians for lengths. For 36 in chord and 18 in rise, R is 18 in, central angle 180°, and inner arc 18π ≈ 56.549 in. With radial depth 2 in, outer radius is 20 in, arc 20π ≈ 62.832 in, outer chord 40 in, and outer rise 20 in.
The chord-and-rise method rejects a rise above half the chord rather than silently choosing a major arc.
Find an arc from three measured points
Three distinct, noncollinear points define one circle. This is useful when an existing circular outline can be measured at three locations but its center is inaccessible. Record every x and y from one origin, in one plane, with one unit. Positive x points right and positive y points up. Separate tape measurements taken from unrelated datums do not form a coordinate set.
P1 is the start, P2 is a point the arc passes through, and P3 is the end. P2 does not have to be the midpoint or highest point. Its position selects which of the two arcs between P1 and P3 to follow. Reversing P1 and P3 preserves the selected arc length but reverses its direction. Choosing a different P2 on the other side of the endpoint chord selects the other arc, which may be longer than a semicircle.
The circle center is where the perpendicular bisectors of two point-to-point chords meet. Subtracting P1 from P2 and P3 first gives relative vectors u and v. The center relative to P1 satisfies 2u · center = |u|² and 2v · center = |v|²; these follow by setting the squared distances from the center to all three points equal. Adding P1 back locates the center in the original coordinate system. The radius is the distance from that center to any of the points. The calculation uses exact coordinate arithmetic for the center and for rejecting repeated or exactly collinear points, then numerical square roots and angles for the arc lengths.
For a hypothetical 36 in span, let P1 be (0, 0) in, P2 (18, 18) in, and P3 (36, 0) in. The center is (18, 0) in and the radius 18 in. Going from left to right through the top follows a 180° clockwise arc. Its length is again 18π ≈ 56.549 in; a 2 in radial depth gives the same 20π ≈ 62.832 in outer arc as the chord-and-rise example.
The through-point determines the long or short arc
These hypothetical points all lie on the circle centered at (0, 0) with a 1 in radius. The endpoints stay at P1 = (1, 0) in and P3 = (0, 1) in; radial depth is zero.
| P2 on the selected arc (in) | Direction from P1 through P2 to P3 | Central angle | Arc length (in) |
|---|---|---|---|
| (0.6, 0.8) | Counterclockwise | 90° | π/2 ≈ 1.571 |
| (−1, 0) | Clockwise | 270° | 3π/2 ≈ 4.712 |
For an included angle θ in radians, inner arc length is Rθ and outer arc length is (R + d)θ. The endpoint chord is a straight distance, so it stays the same for the short and long arcs on one circle. The outer rise along the selected arc runs from the midpoint of the outer chord to the midpoint of the selected outer arc, perpendicular to that chord. It is (R + d)[1 − cos(θ/2)]: below the outer radius for a minor arc, equal to it for a semicircle, and above it for a major arc. A 270° arc therefore does not use the short arc’s rise.
Measurement sensitivity and dimensional limits
Small changes to nearly collinear points can greatly change radius and center. A shallow measured curve may therefore produce a very large radius, and displaying more decimal places would not improve the measurements. Three samples also cannot establish that an entire existing outline is circular; check additional locations before treating the calculated circle as its full profile.
Three-point mode limits each coordinate magnitude, radial depth, circle-center coordinate magnitude, and radius to 1,000,000,000 in (25,400,000,000 mm) for numerical handling. These are software limits, not recommended sizes or installation tolerances. A nonzero arc must also remain numerically distinguishable from 0° and 360°. The original chord-and-rise mode keeps its separate range of 0 < h ≤ c/2.
Inches accept decimals and fractions, including signed point coordinates; millimeters accept decimals. The conversion 1 in = 25.4 mm is exact. Displayed center coordinates are rounded to three decimals, and radius, angle, and arc outputs are numerical approximations with three-decimal display rounding. Zero depth returns identical inner/outer arcs. Radial depth does not include joinery, bending behavior, or material allowance, and the geometry does not establish structural capacity or an approved door/frame outline. For straight frame members, use the miter cut list.